Quality Epoxy Floor Palm Beach
Diamond floor grinder with a vacuum dust extractor on a gray garage slab, with a strip of freshly ground concrete and a filled crack

Concrete grinding and surface prep

Concrete Grinding & Surface Preparation in Palm Beach, FL

A coating is only as good as the slab under it. We diamond-grind the concrete, fill cracks and pits, take off old paint and failing coatings, and check moisture before anything goes down.

  • Diamond grinding
  • Crack repair
  • Old coating removal

Get Your Free Estimate

Three quick fields. We call you back to set up the estimate.

Or call (443) 501-0540

Concrete grinding and surface prep

What Is Concrete Surface Preparation?

Surface preparation is everything done to the slab before a coating goes on. Diamond grinding opens the surface of the concrete so the coating can grip it, and takes off dirt, oil, sealers, paint and old coatings in the same pass.

Then the slab is repaired: cracks are routed and filled, chipped edges and pits are patched, and everything is ground flush. In South Florida we also check the slab for moisture, since water vapor coming up through the concrete can push a coating off.

Prep is part of every floor we coat, and we also do it on its own: grinding off a failed DIY kit, or getting a slab ready for another finish.

Gloved hand filling a crack in a freshly ground concrete slab with gray repair compound using a putty knife

Warning signs

Signs a Slab Needs Real Prep

A slab that looks clean can still be a poor base for a coating. These are the signs we look for at the estimate, and any one of them means grinding and repair come first, not a wash and a roller.

What we look for

  • Paint or an old coating peeling where the tires sit.
  • White powder on the surface, a sign of moisture moving through the slab.
  • Dark patches that show up after rain or sprinklers.
  • Cracks you can fit a coin into, or edges that are chipping.
  • Water that beads up, a sign of an old sealer.

Prep methods

Grinding, Etching or Pressure Washing?

There are three common ways to get a slab ready. Only one opens the concrete enough for a coating system to grip it well.

How diamond grinding, acid etching and pressure washing compare as coating prep
MethodWhat it doesGood base for a coating?
Diamond grindingRemoves the top layer, old paint and sealers, and opens the surfaceYes. It's what we use on every floor
Acid etchingRoughens the surface with acid, then needs rinsing and dryingLimited. It can't remove paint or sealer, and it leaves water in the slab
Pressure washingCleans dirt and loose material off the surfaceNo. It cleans the slab but doesn't open it

DIY kits usually rely on etching or washing, which is one reason they lift under hot tires.

What's included

What Does Slab Prep Include?

These four steps happen before any color goes down.

  • Diamond Grinding

    The surface is opened to a profile the coating can bond to.

  • Coating Removal

    Old paint, sealer and failed coatings are ground off completely.

  • Crack and Spall Repair

    Cracks are filled and damaged areas patched, then ground flush.

  • Moisture Check

    We test for moisture so the system suits the slab.

Diamond floor grinder with a vacuum dust extractor on a garage slab, beside a freshly ground strip and a filled crack

How it works

How Do We Prepare a Slab?

Prep follows the same order on every job.

  1. Step 1: Inspect

    We check the slab for coatings, cracks, oil and moisture.

  2. Step 2: Grind

    Diamond grinding with dust extraction across the whole floor.

  3. Step 3: Repair

    Cracks and damage are filled and ground flush.

  4. Step 4: Clean and Coat

    The slab is vacuumed clean and ready for the coating system.

Why it matters

Why Do Coatings Peel?

When a garage coating fails, the cause is almost always under it.

  • No Grinding

    A coating over washed or etched concrete has less to grip, and lifts under hot tires.

  • Old Paint Left On

    A new coat over old paint is only as strong as the old paint's bond.

  • Moisture Ignored

    Water vapor from below can push a coating off a slab that wasn't checked.

Cost

What Does Concrete Prep Cost?

Prep cost depends on the size of the slab and what's on it. Grinding a clean slab is quick; removing a thick failed coating or repairing many cracks takes longer.

Prep is included in every coating estimate we give, and we price prep-only work at a free estimate too.

Epoxy floors and slab moisture in South Florida

What moves the price

  • Square footage
  • Coatings to remove
  • Crack and spall repair
  • Moisture conditions

Related services

What Goes on the Prepared Slab

Once the slab is ready, one of these finishes it.

Where we work

Slab Prep Across Palm Beach County

We grind and prepare slabs in West Palm Beach and these cities and towns.

Asked often

Concrete Grinding and Prep Questions

Is grinding dusty?

We grind with vacuum dust extraction connected to the grinder, which captures most of the dust at the source.

Can you remove a peeling DIY epoxy kit?

Yes. Failed kits are one of the most common things we grind off before a new floor.

Will the cracks show after coating?

Filled and ground cracks are usually hard to see under flake. A crack that is still moving can come back, which we'll point out at the estimate.

Why does moisture matter in South Florida?

Slabs on grade here can carry moisture from below, and water vapor pushing up can lift a coating. We check before we choose the system. See our slab moisture guide.

Do you prep floors for other finishes?

Yes. We can grind and repair a slab for another installer's finish, like tile or polished concrete prep.

Free on-site estimate

Get a Free Slab Prep Estimate

Tell us what's on the floor now and roughly how big it is. We'll check it at the free estimate.

  • Free on-site estimate
  • Slab checked for moisture
  • Concrete ground before every coating

Tell Us About Your Floor

Or call (443) 501-0540

Call